• <legend id="7b727"></legend>

  • <legend id="7b727"></legend>

    1. NEWS


      XURUI ALLOY

      Why are the parts of the mill easy to wear

      Release time:

      2014-06-07

      Author:

      Source:


      Abstract

      In the previous introduction of mill knowledge, we have shared with you a lot of little knowledge about the mill, such as the maintenance and maintenance of the mill, the inspection and replacement of the vulnerable parts of the mill. Today I want to share with you why the mill parts are easy to wear, and users who do not know need to pay attention to it.
      In the previous introduction of mill knowledge, we have shared with you a lot of little knowledge about the mill, such as the maintenance and maintenance of the mill, the inspection and replacement of the vulnerable parts of the mill. Today I want to share with you why the mill parts are easy to wear, and users who do not know need to pay attention to it.
      First of all, the nature of the material will affect the use of the mill, for the mill, the size of the material added to it must be appropriate, neither too large nor too small, small can not fully play the effect, and large will block the feed port of the equipment. Once such a situation occurs, it is better to affect the normal production, but it can be used normally if it is cleaned up in time. A bad point will damage the impeller of the equipment, and it can only be used after being sent for maintenance. Therefore, the mill must choose good materials before working.
      When the screw on the mill is loose, it will also affect the parts of the mill. Many parts of the mill are fixed by screws, and the equipment in the work of the movement is often more intense, after a long time, these screws are easy to loosen, so that the equipment in the process of work abnormal noise. Therefore, when the mill is abnormal, it is necessary to stop the machine in time and check whether the screw is loose, and if so, it is necessary to tighten it in time.
      In addition, in the case of material to start the mill, the pressure of the motor will increase, when the degree is more serious, the motor will burn out. Therefore, before starting the mill, be sure to ensure that the equipment is empty, and then add materials to it after starting.
      There is also the mill lubrication is not in place. Regular lubrication is an extremely important step in the maintenance of the mill. If the mill is not maintained in time, the wear of the parts will become more and more serious, so that it cannot be used at all. Therefore, after the equipment has been used for a period of time, be sure to check its wear and add lubricating oil as needed.
      There is a lot of little knowledge about flour mills. I don't know what you need. However, in daily use, if you encounter any problems about the mill, you can call our hotline for consultation.

      Recommended Reading


      What are the factors that affect medium frequency furnace steelmaking?


      Common impurity elements in steel are P, S, H, N, O and so on. These elements play a harmful role in the performance of steel under normal circumstances, but some of them can also play a beneficial role under certain conditions and become specially added alloying elements.

      2014-05-10

      Ultrafine mill develops with the development of paper industry


      "Papermaking" is one of the four great inventions in ancient China, which fully illustrates the wisdom and wisdom of the working people in ancient China. We all know that the earliest paper-making method was produced by wood processing, but with the development of the times and the continuous progress of science and technology, the paper we use now is rarely made of wood, but stone powder paper.

      2014-05-22

      Why are the parts of the mill easy to wear


      In the previous introduction of mill knowledge, we have shared with you a lot of little knowledge about the mill, such as the maintenance and maintenance of the mill, the inspection and replacement of the vulnerable parts of the mill. Today I want to share with you why the mill parts are easy to wear, and users who do not know need to pay attention to it.

      2014-06-07

      Message


      To provide you with quality products and services

      亚洲成AV人无码综合在线_欧美在线精品一区在线观看_中文国产成人精品少久久_国产精品内射婷婷一级二